Jims Catalogue

VALVE TRAIN TOOLS

2

NEW

3

11

ADAPTERS FOR 7MM VALVE GUIDES The JIMS head holder tool makes pressing valve guides in and out simple. These adapters are required to update JIMS earlier tool No.2240 shown below for 7mm Valve Guides. For more details see No. 2240-IS instructions. 2240-19 - 7mm Assembly Pilot 2240-11-4 - 7mm Insert

6

4

6

10

8

2

7

9

8 1

3 6 4

5

COMPRESSION RELEASE VALVE TOOL GUIDE FIXTURE FOR DRILLING COMPRESSION RELEASE Use this tool for machining all Twin Cam ® heads 1999 and later to install JIMS ® No.727K compression release valves. Install on the front or rear head with or without the valves installed. Simply drill, spot face, tap and install compression release valves No.727K. For more details see No. 1169-IS instruc- tions. No. 1169 - Use on all Twin Cam ® “A” or “B” models. PARTS AVAILABLE SEPARATELY NO. QTY. DESCRIPTION PART NO. 1 1 THREAD TAP TOOL 1169-1 2 1 DRILL/TAP FIXTURE 1169-2 3 1 STEPPED DRILL 1169-3 4 1 TAP EXTENSION 1169-4 5 1 DRILL BIT 2224 6 3 SET SCREW 2221 7 1 STOP COLLAR 2227 8 2 FLAT WASHER 2014 9 2 MOUNTING SCREW 2016 10 1 DRILL BUSHING 2219 11 1 TAP MAGIC 1698 12 1 INSTRUCTION SHEET 1169-IS

5

1

7

NEW

13 12

11

9 8

15

10

11

PARTS AVAILABLE SEPARATELY 2 1 ADAPTER, INT, 1986-03 883 XL,, ALL T/C EXH 2240-2 3 1 ADAPTER, INT, B/T, EVO, 1986 XL1100 EXH. SHOVELHEAD AND 1986-03 883 EVO XL 2240-3 4 1 ADAPTER, INT, SHOVEL HEAD / EXH BIG TWIN, EVO, 1986 1100, XL, MOST ALL T/C 2240-4 5 1 ADAPTER, INT / EXH, IRONHEAD XL 2240-5 6 1 ADAPTER, INT, 1987-1100 / 1988-03 1200 XL, EVO 2240-6 7 1 ADAPTER, EXH, 1987-1100 / 1988-03 1200 XL, EVO 2240-7 8 1 PILOT .306 DIAMETER 2240-16 9 1 PILOT .371 DIAMETER 2240-17 10 1 PILOT .338 DIAMETER 2240-18 11 1 PILOT 7MMDIAMETER 2240-19 12 1 INSERT, .310 DIAMETER 2240-11-1 13 1 INSERT, .375 DIAMETER 2240-11-2 14 1 INSERT, .342 DIAMETER 2240-11-3 15 1 INSERT, 7MMDIAMETER 2240-11-4 16 1 INSTRUCTIONS 2240-IS Comes with adapters to fit all H-D ® and aftermarket heads. Adapters are supported by a support stand. Makes pressing valve guides in and out simple. A spe- cial guide alignment shaft is designed into this tool. This shaft holds the right angle for the best possible guide installations. Save time and money by installing the guides, in line, with the valve seats, time and time again - for much less seat grinding. For more details see No. 2240-IS instructions. No. 2240 - See Applications Below. HEAD HOLDER (VALVE GUIDE REMOVER AND INSTALLER) NEW NO. QTY. DESCRIPTION 1 1 BASE ASSEMBLY PART NO. 2240-I

COMPRESSION RELEASE THREAD TAP TOOL For cutting threads in the cylinder head to install JIMS ® compression release valves. Tap Size: M10 x 1.0. Use with 9mm (.354”) pilot. No. 1169-1 - Use on all Big Twins and XL engines.

144