Custom Chrome Catalogue

GENERAL

JIMS Rear Axle Nut Torque Adapter

Motion Pro Jumbo Chain Tool Kit • Ultra heavy duty tool for breaking and riveting roller chain • Fits all 520, 525, 530 and 630 standard or O-ring chains, plus industrial chains from #50-#80 • Pushes the pin completely through the chain link and rivets the same size chain with the included rivet adapter • Tool body may be mounted to a work bench for production work, held in a vise or by the handle • When bolted to a surface, an air or electric wrench may be used to break chain • Body bolt requires a 13⁄16" (21 mm) wrench and extractor pin uses a 9⁄16" (14 mm) wrench or socket 5008135 Chain tool ����������������������������������$131.99 5008935 Replacement pin ��������������������������$8.99

Assists in adjusting the drive belt tension or rear wheel alignment. Eliminates the need to remove the mufflers to perform this service. Designed with a 1/2" drive receiver hole for inserting a torque wrench allowing the axle nut to be torqued from an offset position 622045 FL Touring Models 06-Up ����������$40.99

Motion Pro Chain Breaker Tool A tough tool designed for shop use, also makes a perfect tool kit item. Properly used, the tool will break hundreds of chain links without failure. Pushes chain link pin completely through link. Handle folds to fit small tool pouch. Replaceable pin is heat treated and hardened for long life. For shop use, tool may be used with an air or electric impact wrench. 5008001 Fits all 420 to 630 chains ����������$24.99 5008002 Replacement pin ��������������������������$3.99

622061

JIMS 3rd Hand Axle Tool If you have noticed, as you are torquing down the axle nut after you set the proper belt tension (Deflection), the welded axle nut will move to the low side of adjuster cam. This movement will allow the belt to lose adjustment. Now with the “JIMS 3rd Hand Axle Tool”, you won’t need to find a helper to hold the nut or have to reach around the tire yourself to keep the nut from moving. Just place this tool over the welded nut on left side with the neck portion of tool resting over the swing arm. Hand screw the adjusting screw to take up any slack in tool. Torque the axle nut from the right side knowing that the welded nut will not turn allowing the belt to lose its adjustment. Sold each. 622061 For all 02-14 FL models ��������������$63.99

JIMS Late Sealed Wheel Bearing Race Removal and Installation Tool Use to remove and install "new style" sealed wheel bearings without damaging the wheel. 400394 Fits 00-14 Twin Cam models and all 00-14 Sportster, Buell, and Buell Blast models ������������������������������$339.99

Motion Pro Quad Stake Chain Rivet Kit Use in conjunction with the Motion Pro Jumbo Chain Tool. This rivet kit will quad stake chain, so it looks like a factory job. 5008142 Complete kit ��������������������������������$21.99

JIMS 25mm Wheel Bearing Puller Tool This tool is used to remove the new front 25mm H.D. wheel bearings on most of the 07-14 ABS or non-ABS wheels. Includes puller and installer. Note: This tool must be used with the current JIMS wheel bearing installer/remover tool No.1042 (CC# 400394). 640093 For use on 25mm bearing wheels ��������������������������������������������������������������������������������������������� $62.99

Swingarm Bearing Tool for Softail Models Easily installs or removes swingarm spherical bearings on all Softail models from 84-14. Also works on front fender pivot bearings on FLSTS models from 97-03. 20900 Swingarm bearing tool ������������$56.99

16

*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. All parts are sold each unless otherwise noted. Retail prices may reflect an each quantity.

16.38

Please see Cautionary Information in back of catalog.